Mapei Ultrabond Eco 575 – Premium Wall Base Adhesive

Share this:

Description

Description:

Ultrabond ECO 575 is a premium wall base adhesive specifically designed to provide superior bond and impact resistance for rubber, vinyl and carpet wall base. Ultrabond ECO 575 also has been recently reformulated to offer even greater grab and wet strength, keeping corners wrapped tight. Its acrylic-based, light-coloured formulation won’t stain even the whitest wall base. In addition, Ultrabond ECO 575 can be used to install various types of carpet in vertical/wall applications.  

Application:

As an Adhesive for Wall Base (rubber, vinyl and carpet)

Trowel Application Method
  1. Read all installation instructions thoroughly before installation.
  2. Select the appropriate notched trowel (see “Approximate Product Coverages” section).
  3. Spread adhesive evenly over the wall surface, keeping the trowel at a 45° angle to the substrate. Or spread adhesive evenly over the back of the wall base, keeping the trowel at a 45° angle to the back of the base.
  4. Install the wall base into the adhesive while it is still fresh.
  5. For working time and flash time, refer to “Application Table.”
  6. Install cove base per the manufacturer’s instructions.
  7. Roll the entire surface with a small roller. Always roll towards the last piece of base installed.
  8. Promptly clean any adhesive smudges from the flooring material’s surface with water while the adhesive is still fresh/wet.
  9. Clean tools with water while the adhesive is still fresh/wet. Use mineral spirits once dried. Use caution with mineral spirits, which may be harmful to some materials.
Cartridge Application Method
  1. Read all installation instructions thoroughly before installation.
  2. Ultrabond ECO 575 can be applied to the back of the base or directly to the wall.
  3. Apply the adhesive evenly using a nozzle.
  4. Install the wall base into the adhesive while it is still fresh.
  5. For working time and flash time, refer to “Application Table.”
  6. Install cove base per the manufacturer’s instructions.
  7. Roll the entire surface with a small roller. Always roll towards the last piece of base installed.
  8. Promptly clean any adhesive smudges from the flooring material’s surface with water while the adhesive is still fresh/wet.
  9. Clean tools with water while the adhesive is still fresh/wet.
  10. Use mineral spirits once dried. Use caution with mineral spirits, which may be harmful to some materials.

As an Adhesive for FRP Panels

  1. Read all installation instructions thoroughly before installation.
  2. Select the appropriate notched trowel (see “Approximate Product Coverages” section).
  3. Some product backings may require cleaning, sanding or “roughing up” to improve the mechanical bond. Perform a test bond before application.
  4. Measure and pre-fit FRP panels to the wall before applying adhesive.
  5. Ensure that wall surface is clean and free of dust and bond-breaking substances before applying adhesive.
  6. Uncoated gypsum wallboard and other porous surfaces should be primed with a skimcoat of adhesive.
  7. Spread adhesive evenly over the wall surface, keeping the trowel at a 45° angle to the substrate.
  8. Depending on temperature, humidity and surface porosity, wait 5 to 20 minutes before attaching the panel to the substrate.
  9. For working time and flash time, refer to “Application Table.”
  10. Install FRP panel per manufacturer’s instructions.
  11. Roll the entire surface with a heavy-duty extension hand roller to expel air and ensure proper bond. Press firmly with the roller, working from the center to the outer edges.
  12. Temporary bracing may be necessary if wall panels are not straight.
  13. Promptly clean any adhesive smudges from the flooring material’s surface with water while the adhesive is still fresh/wet.
  14. Clean tools with water while the adhesive is still fresh/wet.
  15. Use mineral spirits once dried. Use caution with mineral spirits, which may be harmful to some materials